PELICE 2022 Brought Everything From Taguchi To Board Quality Control

Article by Rich Donnell, Editor-in-Chief, Panel World September 2022

PART THREE: This is the third of a four-part series summarizing the presentations delivered during the Panel & Engineered Lumber International Conference & Expo (PELICE) held this spring and hosted by Panel World in Atlanta March 31 to April 1. The first two parts appeared in the May and July issues of Panel World, and the fourth and final selection will be in the upcoming November issue.

ATLANTA, Ga. – Terry Liles, director of raw materials, Huber Engineered Woods, dug into the application of EVOP (Evolutionary Operation) and Taguchi Design. He defined EVOP as an ongoing mode of using an operating full-scale process so that information on how to improve the process is generated from a simple experimental design while production is underway.

He noted two methodologies for conducting EVOPs: Factorial Designs, a scientific experiment that determines the influence of multiple factors on the subject, while assuming the process is consistent or under control; and Robust Product Design (or Taguchi Design), a methodology to improve the quality of a product by minimizing the effect of variation without eliminating the causes, and with minimal sensitivity to variation in uncontrollable factors or noise.

With either design approach, it’s most important to understand and state the objective for the experiment. “If you can’t define the purpose, why are you doing it?” Have a general model of the process and understand the variation; that is, the total variation is the sum of the real product variation and the measurement system variation; and the measurement system variation is the sum of the variation due to repeatability and due to reproducibility.

The sampling strategy is of utmost importance, including the number of samples and tests; and data integrity is crucial. “Am I collecting the right data to answer the questions I’m asking?”

One of the advantages of EVOP is the inclusion of many team members, Liles said, and an effective means of communication is essential such as an information board with results, statistics, deviations, graphs, etc.

He noted that Taguchi design as an EVOP is most suitable with a larger number of factors and levels, and when fewer experiments are needed; when you’re able to measure the impact of uncontrolled variables; and when there’s a targeted response objective. Whereas Factorial Design is better when the number of factors and levels is small, experiments are not time-consuming and the costs for the experiments are low, and when a combination of factors could be significant contributors to the response.

Left to right, Tim Young, Justin Price, Terry Liles and Jeff Vaughn get into experimental methodology.

Jeff Vaughn, eastern regional technical and CI manager for Roseburg, also addressed Design of Experiment Methodology as compared to traditional model of experimentation. The current state of experiments and trials is mostly the “best guess” approach and “one factor at a time” approach, Vaughn said.

The best guess approach has advantages through the technical and theoretical knowledge and practical experiences of team members, but this approach is generally not very efficient and can exclude better solutions. The one factor at a time approach is a simple, baseline approach with simple analysis, but fails to consider possible interaction between the factors and doesn’t gain enough data to deliver statistical significance.

An alternative approach is statistical design of experiments, including Taguchi, which refers to the process of planning and executing an experiment so that the proper data will be collected an analyzed through statistical methods, resulting in effective and unbiased conclusions.

QUALITY CONTROL

A series of presentations addressed Quality Control, including one by Richard Lepine, general manager with Argos Solutions. He touched on automatic grading and surface defect inspection technology, initially showing its obvious benefits (speed, defect size and location, no labor issues, verification, etc.) compared to visual inspection.

He defined new standards for TFL surface defects (such as dirt, spots, fibers, scratches, and area size) and revealed Argo’s automated detection system for printed pattern TFL, including detection of hidden defects in complicated patterns, automatic adjustment for inaccuracies in paper, stretch/shrink, rotation; special illumination; and no learning mode required; and noted the Argos use of different light angles; and finally addressed Argos’ real time monitoring and database system and reporting for categorization and statistical analysis.

Keith Mays, president of EWS North America, addressed a range of quality control products from Electronic Wood Systems GmbH, Baumer Inspection Gmbh and Monitor Plus GmbH. He hit on spark detection/extinguishment and board scanning and measurement from EWS, and the SicoScan system in collaboration with Siempelkamp, and within SicoScan the EcoScan NEO – FBD (foreign body detector) and FLY area weight measurement.

He provided detail on Baumer’s ColourBrain 4.0 optical top and bottom inspection of raw board, including a new illumination module, running through a Q-Live server environment that provides database, networking and is user-friendly. He addressed Q-Brain, which classifies the defects while QLive provides full transparency to leverage process optimization.

He also spoke in detail on Monitor Plus, a system that monitors product quality and actives alarm signals or a production stop if quality specifications are not met. It features SMART camera technology and is designed for any kind of conveying system and entails the latest data processing for its numerous product scanning and detection tasks and functions ranging from bowing to cupping, twisting, curvature, to number of drill holes in wood components, particleboard edge porosity, laminate color and glossiness, profile and contour measurement, through multiple line laser thickness measurement.

Continuing with the theme of board scanning and quality control, Michael Spurgin, sales manager North America for Limab, spoke about the different building materials that Limab’s scanning and measurement system caters to. He said Limab’s thickness measurement eliminates the effects from vibrations and bumps.

He noted several benefits with in-line measurement, from consistency to reduced downtime and increased yield; and the benefits of non-contact versus contact roller systems, including measurement on soft material like insulation to thin board to high speed and rough surfaces, while measurement starts immediately at the front edge of panels.

He pointed to multiple locations for Limab installation in a typical board processing line, including after the press, either before or after the sander (verifying that the final product is within tolerances), and with double effectiveness if measurement scanners are located both before and after the sander while using one PC; as well as a three point sander configuration including between the heads.

Jason Kovacik, sales manager with Finna Sensors, spoke on production enhancements and profitability by using IoT data-driven moisture control measurement sensors. He reviewed why IoT sensors are trending, including real-time process data, visibility of process trends and conditions, and more focused analysis. Compared to non-enabled sensors, IoT sensors enable cloud-based updates, remote diagnostics, and monitoring of sensor health and performance.

Kovacik spoke on the criteria for integrating IoT-enabled sensors into your process, including partnering with the right organization and having a strategy for adoption. More technology-specific, he focused on Finna’s OMNIR noncontact, non-destructive, real-time moisture control measurement, which features white light, near-infrared energy filtering and resonance frequency of water molecules, and with advantages built into the associated and minimized system hardware.

Kovacik talked about the company’s RF technology including an in-line meter that delivers a full moisture map of boards/pieces; and he addressed their in-line acoustic technology for strength grading.

Finna’s products can be implemented and provide value throughout the process, from incoming raw material to drying, energy production and final product quality.

AIR TREATMENT

Jaymie Deemer, President of Nestec, Inc., gave an in-depth look at dryer WESP and RTO systems, including the complexities of wood dryer emissions sometimes associated with the dryer technologies and with the particulate materials themselves. Some of these issues, as well as others, can contribute to common ESP and RTO issues and problems.

Nestec President Jaymie Deemer provides WESP and RTO dos and don’ts.

He said, “Wet ESP performance and design of critical components are key to reliable operation, and pointed to numerous such features in both WESP and RTO design, including, in the former, isolable electric fields, extended flushing, simple electrode alignment, irrigation, plug resistant spray nozzles, power supply, continuous loop blowdown, high temperature water flush, caustic grade; and in the latter, proper media, draft arrangements, multiple burners, and proper construction materials such as mastic coatings to protect the shell from condensation, and which materials to avoid such as low grade stainless steel.

Rodney Schwartz, vice president Sales & Business Development, Dürr Systems, spoke on the development and testing of new WESP design enhancements including an optimized electrode and tube design. After reviewing various factors that influence WESP performance, and issues and concerns with current designs, he said Dürr approached producers and operators to get their input on current designs. The feedback included: tubes and electrodes get dirty and are difficult to clean, potentially impacting collection performance; capital cost is too high; installation time is too long; foaming problems; mist carryover into RTOs; performance drop when flushed.

Dürr promptly set goals for a new WESP based on the feedback, including modular shipping design, better fabrication, flexible sizing, new patentable ideas, online cleaning, offline flushing.

Dürr developed a 1/6th to-scale test model and performed testing over 16 weeks with 27 separate flow tests and 55 different particulate removal tests. Testing included various configurations of electrodes, including bottom mounted discharge electrodes that proved highly effective, including the use of a High Area Trap (HAT) that showed numerous benefits.

They then built a to-scale 25,000 acfm pilot WESP that was installed at an OSB customer site in the Southern U.S. and was tested for 10 months downstream of rotary flake dryers. The new designs scored high compared to older designs on filterable particulate removal, organic condensable particulate removal, enhanced spray system cleaning and showed numerous other benefits.

The key features of the new product include maximum removal efficiencies, reliable operation, low operating costs, and significantly reduced maintenance.

Steve Jaasund, Geoenergy Products Manager for LDX Solution, addressed the benefits of RCOs for wood dryer VOC control, which is not a common practice. He noted the principle of operation for an RCO is similar to the RTO while the catalyst allowed lower combustion chamber temperature and offers significant energy savings.

He spoke on scenarios for catalyst deactivation such as poisoning, sintering and masking, but noted poisoning is not a likely problem for wood fired dryers as common poisons are not present in flue gases, alkali sintering occurs at higher tempertures than are typical for an RCO, and while masking can occur if particulate concentration is too high, he recommended ensuring that particulate loading (inlet fly ash) is low enough, upsizing the wet ESP during the initial design and/or adding a second field to the wet ESP, implementing catalyst wash out on an as-needed basis, and conducting regular catalyst performance testing.

His energy consumption chart showed significant annual savings (annual fuel cost, annual electric cost) with an RCO system compared to RTO at various gas prices, with RCO payback in a few years. The path forward, Jaasund said, is to install test blocks or thief baskets in existing RTOs operating on a wood fired dryer, and he noted existing RTOs can be catalyzed easily.

Latest News

Huber Takes Another Swing

Huber Engineered Woods appears to be looking at building its sixth OSB plant in Shuqualak, Miss. in Noxubee County. In March, the U.S. Army Corps of Engineers and the Mississippi Dept. of Environmental Quality released a joint public notice for Huber’s application for a permit pursuant to the Clean Water Act, and in May MDEQ released a Large Construction Notice of Intent under the Large Construction General Permit applied for by Huber at Shuqualak…

48 Years Of Westmill & Still Going Strong

Established in 1975, Victor Crondahl started Westmill Industries supplying parts and equipment to the Canadian plywood manufacturing industry. Now, nearly five decades later Westmill continues to grow under its current owner, Mike Crondahl, son of the founder. Westmill has become a world leader in the design and manufacture of veneer drying equipment and technologies. Twenty-five years after Westmill installed the plywood…

Georgia-Pacific Camden Plywood Invests $18 Million

It was in the late 1800s when the small community of Camden, Tex., welcomed its first forest products mill. What began as the W.T. Carter Lumber Co. is today one of Georgia-Pacific’s largest plywood operations. To ensure its longevity for years to come, Georgia-Pacific is embarking on a $18 million upgrade that will modernize the plant and help increase efficiency…

Roseburg Makes Major Decision

Roseburg Forest Products, which announced in April a $700 million investment over the next four years to expand operations in southern Oregon, including a $450 million MDF plant in Dillard, Ore., has selected Siempelkamp as the primary supplier of the MDF plant, including a 10 ft. x 42.1 m ContiRoll continuous press. The companies noted that in 1969 Siempelkamp supplied Roseburg Lumber with its very first composite panel press line…

APA Board Adds Beers As Trustee

APA, The Engineered Wood Assn. Board of Trustees has added John Beers III as its newest member. He joins the APA Board of Trustees, filling the position vacated by Andy Konieczka’s resignation and move to a new role within Georgia-Pacific. Beers currently serves as the president of the structural panels business at Georgia-Pacific…

J.M. Huber Corp. Receives Management Honor

J.M. Huber Corp. (Huber) has proudly announced it has been selected as a 2023 U.S. Best Managed Company Gold Standard honoree. Sponsored by Deloitte Private and The Wall Street Journal, the program recognizes outstanding U.S. private companies and the achievements of their management teams. The 2023 designees are U.S. private companies that have…

Time To Stretch The Legs

Article by Rich Donnell, Editor-In-Chief, Panel World May 2023 – In May, I depart for my 17th consecutive Ligna in Hannover, Germany. If the pandemic hadn’t canceled the event in 2021, I suppose this would have been 18. Regardless, I’m sure by now you’re thinking this guy…

Dieffenbacher Names New Energy Unit Director

Wolfgang Lashofer has been appointed as the new Managing Director of Dieffenbacher Energy GmbH, which was formed at the beginning of the year following the acquisition of BERTSCHenergy, based in Bludenz, Western Austria. As Managing Director of Dieffenbacher Energy, Lashofer takes over the management of the newly established Energy Business Unit…

Raute PRS R5 Proving Itself

Raute introduced its Panel Repair Station (PRS) R5 the plywood industry in 2020. Soon there will be 13 units operating in North America. Measuring 33 ft. by 26 ft., the R5 is no larger than most manual repair cells. It requires no foundations, meaning it can be up and running within two weeks of delivery…

India’s Greenpanel Grows With MDF

India’s largest MDF manufacturer, Greenpanel Industries Ltd., has ordered its third MDF plant from Dieffenbacher. The new thin-board line based on Dieffenbacher’s smart plant concept, CEBRO, will be added in Routhusuramala, Andhra Pradesh. That’s the same site where Greenpanel commissioned a Dieffenbacher MDF line with a 56 m long CPS, the longest continuous press in…

Kronospan Announces Further Expansion At Alabama Site

Kronospan will begin construction of a new OSB manufacturing plant on its 460 acre site in Oxford, Ala. The new facility, employing 125, will have a footprint composed of 44 acres of new development, including substantial areas designated for product storage, rail spur and loading docks. Groundbreaking for the $350 million facility is scheduled for later this year…

Dates Announced For Ninth PELICE

The next Panel & Engineered Lumber International Conference & Expo (PELICE) will be held March 14-15, 2024, again at the Omni Hotel in Atlanta, Georgia. PELICE is hosted every other year by Panel World magazine and Georgia Research Institute. This will be the ninth PELICE since its inception 2008…

Panel World Gears Up To Exhibit At Ligna

Panel World magazine and its affiliates will be exhibiting at the upcoming international wood products fair, Ligna, to be held May 15-19 in Hannover, Germany. In addition to Panel World, the Hatton-Brown organization, which dates back to 1948 in Montgomery, Ala., today publishes five business magazines geared to the wood products industry…

LP To Acquire Ontario OSB Facility

LP Building Solutions (LP) and Forex Inc. have entered into a definitive agreement for LP to acquire the assets owned by Wawa OSB Inc., a subsidiary of Forex Inc. The manufacturing facility in Wawa, Ontario will be converted into an LP SmartSide trim and siding mill. The transaction, which is subject to court approval and customary closing conditions, is expected to be completed in early May 2023…

Georgia-Pacific Names New Building Products Leader

Andy Konieczka, currently President–Structural Panels, will assume the leadership role for the building products business as Executive Vice President–Building Products. Konieczka will report to the company’s President and CEO Christian Fischer. Konieczka has been with Koch companies since 1992. In 2006, he joined Georgia-Pacific, holding strategy, optimization and management roles in wood and fiber, and…

Structurlam Files For Bankruptcy, May Sell To Mercer International

Structurlam Mass Timber Corp. has filed for bankruptcy protection and agreed to sell the company’s new Conway, Ark. CLT plant and its Canadian assets for $60 million, pending court approval. Structurlam entered the asset-purchase agreement with Mercer International Inc., a global forest products company which operates a mass timber facility in Spokane, Wash. However, Mercer’s purchase is subject to a better offer in a court-monitored process…

Panel Producers Make Key Hires

Roseburg has named Lorraine Russ as Director of Structural and Specialty Panels, a newly created role in which she will lead the company’s commercial efforts for softwood and hardwood plywood. Russ comes to Roseburg with a solid depth of leadership experience in strategic sales planning, product innovation and commercialization, and marketing after more than a decade in the building products industry….

TP&EE Sets 2024 Show Dates

Hatton-Brown Expositions LLC announces that the next Timber Processing and Energy Expo (TP&EE) will be held September 25-27, 2024 at the Portland Exposition Center in Portland, Ore. The 2024 show will be the sixth biennial TP&EE to be produced since 2012 by Hatton-Brown Expositions, LLC, an affiliate of Hatton-Brown Publishers, Inc. and of Timber Processing, Panel World and Wood Bioenergy magazines. All of the TP&EEs have been held at the Portland Exposition Center. (The 2020 event was canceled due to…

Roseburg Announces Massive Investment

In a much-anticipated announcement, Roseburg Forest Products revealed in last week its plan to invest $700 million during the next four years to upgrade and expand its manufacturing operations in southern Oregon, including the construction of a MDF facility in Dillard, current site of multiple operations and where the company was founded nearly 90 years ago. The total investment package includes the creation of two new manufacturing plants, and technological improvements and upgrades at existing plants in rural Douglas and Coos counties…

LP Adds New VPs

LP Building Solutions (LP) has announced that Libby Berman has been named Vice President, Chief Tax Officer and Bob Hopkins has been named Vice President, Treasurer. “Bob and Libby have been invaluable contributors to the LP team for many years now,” says LP Executive Vice President and Chief Financial Officer Alan Haughie…

Find Us On Social

Newsletter

The monthly Panel World Industry Newsletter reaches over 3,000 who represent primary panel production operations.

Subscribe/Renew

Panel World is delivered six times per year to North American and international professionals, who represent primary panel production operations. Subscriptions are FREE to qualified individuals.

Advertise

Complete the online form so we can direct you to the appropriate Sales Representative. Contact us today!